An Easy Tutorial for Bathtub Installation
An Easy Tutorial for Bathtub Installation
Blog Article
They are making a few good points on A Step-by-Step Guide to Installing a Bathtub overall in the article down below.
Setting up a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging project. If the old tub is readily easily accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub as well as position the new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also set in the new one. Make certain you have certified yourself for the task and are comfortable trying it. Instead of working with a contractor to take control of a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This article will aid you set up a brand-new bathtub in your washroom if you have actually currently acquired a new tub as well as do not require to transform the plan of your previous water pipelines.
Your devices as well as product list must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly bothersome due to the limited accessibility that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Protect the faucet in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Using both wooden boards under its feet, place the bath tub in the called for position. The wooden boards are practical in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub till the level reviews degree.
To mount taps, fit all-time low of the outermost flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and inspect all joints and also new pipework for leakages as well as tighten them if needed. Fill the tub and also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been utilized at least when as this will resolve it right into its last placement.
Preparing for the Installation
To start with, the supporting frame provided with the bathroom must be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with wetness as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can crack rather very early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that review about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while perusing the web. Sharing is nice. Helping people is fun. Thank you for your time. Please come by our site back soon.
Superior emergency plumbing? We're here. Report this page